How to Set up a Tub: Install an Acrylic Bathtub as Well as Tub Surround

How to Set up a Tub: Install an Acrylic Bathtub as Well as Tub Surround

Blog Article

Schedule Here

Were you trying to find additional info around A Step-by-Step Guide to Installing a Bathtub?

Installing A Bathtub
Mounting a bath tub isn't exactly brain surgery, but it does need strong plumbing, carpentry, as well as occasionally, tiling abilities. Changing an old bathtub with a brand-new one is additionally a moderately challenging job. If the old bathtub is conveniently obtainable, the task can relocate speedily; if you have to open a wall to eliminate the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either instance, the project is within a home handyman's skills, although you will certainly require an assistant to move out the old tub as well as embeded in the brand-new one. See to it you have actually qualified yourself for the task as well as fit trying it. Rather than hiring a specialist to take over a halfway-completed job, it is much better to take into consideration utilizing one prior to you start. Opportunities are you might require a professional plumber to make tube connections.
This short article will help you set up a new tub in your shower room if you have actually currently acquired a brand-new bathtub and also do not need to change the plan of your previous water system pipelines.
Your tools as well as material checklist ought to comprise the following:
  • New Bathtub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Measuring tape

  • Pipeline Caps

  • Planning for the Setup

    First of all, the sustaining frame supplied with the bath should be fitted (if required) according to the producer's directions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is very important to ensure that if the tap includes a plastic washing machine, it is fitted in between the bath as well as the taps. On a plastic bath, it is likewise practical to fit a supporting plate under the taps unit to prevent strain on the bathtub.
    Fit the flexible faucet adapters to the bottom of both faucets utilizing 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next off, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you utilize all of the provided washers.
    Connect the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath should currently be ready to be suited its last position.

    Removing Old Touches

    If you need to change old faucets with brand-new ones as a part of your setup, after that the first thing you must do is disconnect the water. After doing so, switch on the faucets to drain any water staying in the system. The process of getting rid of the existing taps can be fairly bothersome because of the restricted accessibility that is commonly the situation.
    Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the taps. Have a towel ready for the continuing to be water that will originate from the pipes. When the supply pipes have actually been removed, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from transforming throughout this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
    Prior to moving on to fit the new faucets, compare the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new taps to fit.

    Mounting the Bathtub

    Utilizing both wooden boards under its feet, put the bath tub in the required position. The wood boards are handy in equally spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto four tiny factors.
    The next goal is to make sure that the bath tub is leveled all round. This can be achieved by inspecting the level and also adjusting the feet on the tub up until the level reads level.
    To set up faucets, fit all-time low of the furthest flexible tap port to the ideal supply pipeline by making a compression join; after that do the same for the other faucet.
    Activate the supply of water as well as examine all joints and new pipework for leakages and also tighten them if necessary. Fill up the bath tub and likewise inspect the overflow electrical outlet and the typical electrical outlet for leakages.
    Ultimately, fix the bath paneling as explained in the supplier's user's manual. Tiling and sealing around the tub needs to wait until the bathtub has been utilized at the very least when as this will settle it into its last placement.

    Suitable New Taps

    If the tails of the new taps are plastic, then you will need a plastic port to stop damages to the string. One end of the connector fits on the plastic tail of the tap and the other end supplies a link to the current supply pipes.
    If you need to fit a monobloc, then you will require decreasing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
    Next off, place the tap in the installing hole in the bath/basin ensuring that the washing machines remain in area in between the tap as well as the sink. Secure the faucet in position with the producer provided backnut. As soon as the faucet is safely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with normal faucet adapters. The previous type should be attached to the tap ends initially, tightening only by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have been linked.

    Tiling Around the Bathtub

    In the location where the bath meets the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to split a rigid seal, creating the water to permeate the wall between the bathroom as well as the tiling, leading to complications with wetness as well as possible leakages to the ceiling below.
    You can choose from a selection of coloured sealants to blend in your fixtures and also fittings. They are sold in tubes and also cartridges, as well as can securing gaps approximately a width of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of soaked paper or soft rope. Keep in mind to always fill up the bathtub with water prior to sealing, to permit the motion experienced when the tub remains in use. The sealer can break fairly very early if you do not consider this movement prior to sealing.
    Conversely, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise conveniently available on the market. It is suggested to fit the tiles making use of water-resistant or water resistant glue as well as grout.

    How to Install or Replace a Bathtub

    Find Your Dimensions

    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

    Disconnect the Water Supply and Drain Assembly

    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

    Cut Out the Old Tub

    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

    Install the New Tub

    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

    Secure the Tub

    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    Tools You Need to Install a New Bathtub

    I came across that content about A Step-by-Step Guide to Installing a Bathtub while doing a search on the internet. Are you aware of someone else who is curious about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Why not share it. I thank you for reading our article about Tools You Need to Install a New Bathtub .

    Set An Appointment

    Report this page